Hull Industries' Complete Molding Solution Process - Automatic Material Loading - Mold Design - Thermoset and Composite Molding Presses - Automated Parts Handling - Deflashers - Hull Industries' Complete Molding Solution Process

Press Selection Checklist/Specification

Thank you for your interest in our presses, we are eager to assist you so please be kind enough to provide us important information.

  Shipping and Mailing Address:

Hull Industries, Inc.
59 Industrial Drive
New Britain PA 18901 USA

 Telephone:

888-567-0983 (Toll Free)
215-230-4260 (Local Voice)
215-230-4261 (Local Fax)

Email Address:

info@hullindustries.com
Press Selection Checklist / Specification
 
* Name   Privacy Note:
All information provided in this request form will be used solely to provide you with the information that you are requesting. This information will not be shared with anyone outside Hull Industries.

Thanks for your interest in our products and services.
*
Email
  
  Company  
 

Address

  
   
 
City
   Preferred Method to be Contacted:
 
State
  
  Zipcode
How did you hear about us:
  Country  
  Province/County    
  Phone    
  Fax    
  Type of press: Transfer Compression Shuttle Injection Automatic Compression
    For Compression Press:  Downward Acting Upward Acting
  Type of molding material
(ie: BMC, Polyester, Composite, Etc.)
  Material will be in what form
(ie: Grandular, Bulk, Sheet, Etc.)
  How will material be loaded into press
(ie: Manually, Automatically-Feeder System)
  Size of part to be molded
(Length / Width / Height in inches)		 L   W   H 
  Number of cavities in mold
  Amount of molding material - total shot weight    (transfer press only)
  Clamp tonnage requied
  Transfer tonnage required (transfer press only)
  Hydraulic system operation pressure (psi)
(Our standard press design is based on 3000 psi)
  Clamp stroke required   (inches)
  Transfer stroke required (transfer press only)   (inches)
  Ejector stroke required   (inches)
Moving platen:
Stationary platen:
  Daylight required   (inches)
  Tie rod spacing (left to right) - (transfer, compression,
shuttle, automatic compression presses)		   (inches)
  Tie rod spacing (front to back) - (transfer, compression,
shuttle, automatic compression presses)		   (inches)
  Tie rod spacing (front to back) - (injection press only)   (inches)
  Tie rod spacing (top to bottom)   (inches)
  Platen size (left to right)   (inches}
  Platen size (front to back)   (inches)
  Minimum mold height required   (inches)
  Height required from floor to platen   (inches)
  Are there space requirements that must be considered   Overall height (inches)
  Floor Space - left to right and front to back - (transfer, compression,
shuttle, automatic compression presses)		   Left to right (inches)
  Front to Back (inches)
  Floor Space - length and width - (injection press)   Length (inches)
  Width (inches)
  Heat Platens Required Yes No
  Number of heating zones per platen half
  Heater power required per platen (KW)
  If other than electric, select a platen heating option
  Clamp - fast close   (inches/minute)
  Clamp - pressing   (inches/minute)
  Transfer - fast close - (transfer press only)   (inches/minute)
  Transfer - retract- (transfer press only)   (inches/minute)
  Electrical Requirements - please provide any special requirements for the electric motor, heat and controls (please refer to our product brochures for our standards.)
Options:
  "Smart Mold" System   (proportionall velocity and pressure control (transfer and injection presses) Yes No
  Injection/Compression circuit - (injection press) Yes No
  BMC stuffer - (injection press) Yes No
  Hydraulic Core Pull) Yes No
  Proportional position control - (compression press) Accuracy Required Yes No
  Proportional pressure control - (compression press) Accuracy Required Yes No
  Other special features or requirements: (please be specific)
 
 

30 Ton Compression Press Shipped
Hull Industries' has shipped a custom 30 ton 8 daylight compression press to their customer in Southeast Asia [More ...]
 

500 Ton Compression Press Shipped
Hull Industries' shipped a 500 ton compression press to their customer in Southeast Asia. [More ...]
 

Hull eNewsletter
SUBSCRIBE
 

Past eNewsletters
June 2009

Hull Industries will be participating in ACC 2010 - Click for Information